Swiftech MCW5002 P Manuel d'utilisateur télécharger pdf

Swiftech Inc., 1703 E. 28

St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Parts list

Parts QTY PARTS QTY

MCW5002-P™ assembly 1 Arctic Alumina Thermal compound 1

½” Barb fittings 2 Retention clips 2

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in

damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their

installation. The following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com

for

updates.

1. Preparing your Motherboard

 Remove the existing heat sink

 Carefully clean the CPU.

 Lightly coat the CPU with the provided thermal compound. Only a paper-thin coat is necessary. It should be applied

using preferably a razor blade, or a credit card, held between thumb and index at a 45-degree angle.

2. Install the hose barbs into the MCW5002 Housing.

 Plastic barbs are provided with all the MCW5002 series water-blocks, please do not swap for brass barbs, as cell

corrosion WILL result.

 Thread sealant must be used when making up the threaded connection. The best sealant is 'Plumber's Goop' but

Teflon tape can be used as well.

i. With Goop, fill the threads on the barb and screw in by rotating 1/2 turn forward, 1/4 turn back (this

will help work the Goop into the water-block's female threads). After 24 hrs the goop will be quite

solid.

ii. With Teflon tape, apply 3 to 4 wraps in a clockwise rotation with the threaded end facing you, then

screw into the water-block's female threads without any backwards rotation. The Teflon sealed

connection may be tested immediately.

When properly made up there will be ~3/16" of thread showing under the 'nut’ portion of the fitting.

3. MCW5002-P™ water-block installation

The MCW5002-P water-block installs using Intel’s stock socket 478 retention frame. Installation procedure to the

motherboard is essentially the same as for the MCW5000 series water-blocks, pictures of which are shown

below.

Step 1

Position your block inside the

retention frame. Put both clips in

place for the next step, by simply

slipping the hook of each clip into

the holes of the retention frame.

Step 2

While maintaining the opposite

side of the block to prevent it from

tipping over, push down on the

clips’ thumb-tab until the hook

catches the hole in the retention

frame.

Step 3

Keep maintaining pressure on the

block to prevent it from tipping

over, and hook-down the second

clip.

Installation is complete!

Last revised 1-28-04 – copyright Swiftech

1 2

Résumé du contenu

Page 1 - Parts list

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Parts list Parts QTY PARTS QTY MCW5002-P™ assembly 1

Page 2 - Swiftech Inc., 1703 E. 28

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 4. Connecting the water-block(s) to the cooling circ

Commentaires sur ces manuels

Pas de commentaire

Swiftech MCW5002 P Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour ordinateurs Swiftech MCW5002 P. Swiftech MCW5002 P User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour ordinateurs Swiftech MCW5002 P