Swiftech MCW5000 PX Manuel d'utilisateur télécharger pdf

Swiftech Inc., 1703 E. 28

St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Parts list

Parts QTY PARTS QTY

MCW5000-PX™ assembly 1 Arctic Alumina Thermal compound 1

Tube inserts 4 Hex L-key 1

Tube removal tool 1 Motherboard hardware kit 1

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in damage

to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The

following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com

for updates.

1. Before you install the MCW5000-PX™ water-block:

a. Prepare two pieces of tubing of sufficient length to connect to

the rest of your circuit. The cuts must be square as shown in figure

1 or leaks may occur:

b. Install the provided plastic tube inserts at each end of the tubes,

as shown in figure 2: these inserts are absolutely imperative when

using any kind of soft tubing, such as vynil, ClearFlex, Taigon, etc...

Square cut

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

c. Spread a little bit of grease or soap (Vaseline,

dishwashing liquid, etc..) around the tubing. It helps

pushing the tubes in, particularly with Clearflex

tubing, which features a very “sticky” surface.

d. Fully insert both tubes into the fittings. The tip of the plastic tube inserts should

be flush with the inlet and outlet openings, as shown in figure 4 above. Inserting the

tubes requires a firm push, accompanied by a twisting motion.

2. Preparing your Motherboard

a. Remove the existing heat sink

b. Carefully clean the CPU.

c. Lightly coat the CPU with the provided thermal compound. Only a paper-thin coat is necessary. It should be applied using

preferably a razor blade, or a credit card, held between thumb and index at a 45-degree angle.

Fiber washer

and Hex lock-nut

on back side of

the MB

Standoff

Install standoff in each one of the four holes surrounding the

socket. Keep the standoff centered over the MB holes, and

secure with fiber washer and locknuts on backside of the MB.

Maximum torque not to exceed 16 in lb

Page 1 of 3

1 2 3

Résumé du contenu

Page 1 - Parts list

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Parts list Parts QTY PARTS QTY MCW5000-PX™ assembly 1

Page 2 - Swiftech Inc., 1703 E. 28

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 3. Installing the MCW5000-PX™ water-block Block orientat

Page 3

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Page 3 of 3

Commentaires sur ces manuels

Pas de commentaire

Swiftech MCW5000 PX Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour ordinateurs Swiftech MCW5000 PX. Swiftech MCW5000 PX User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour ordinateurs Swiftech MCW5000 PX